About
Community
Bad Ideas
Guns & Weapons
Irresponsible Activities
KA-FUCKING-BOOM!
Locks and Security
Scams and Rip-offs
Drugs
Ego
Erotica
Fringe
Society
Technology
register | bbs | search | rss | faq | about
meet up | add to del.icio.us | digg it

Master Combo Lock (By a Locksmith!)


NOTICE: TO ALL CONCERNED Certain text files and messages contained on this site deal with activities and devices which would be in violation of various Federal, State, and local laws if actually carried out or constructed. The webmasters of this site do not advocate the breaking of any law. Our text files and message bases are for informational purposes only. We recommend that you contact your local law enforcement officials before undertaking any project based upon any information obtained from this or any other web site. We do not guarantee that any of the information contained on this system is correct, workable, or factual. We are not responsible for, nor do we assume any liability for, damages resulting from the use of any information on this site.




--------------------------------------------------------------------
TC PUBLICATIONS -- APRIL 29, 1991 -- "Master Combination Locks"
--------------------------------------------------------------------

MASTER COMBINATION LOCKS

Almost all combination locks, including safe locks, operate on
the same basic principle. The dial is turned to a preselected
series of numbers that line up the unlocking mechanism and allow the
lock to open. People always lose the combinations for these locks.
If you have a thorough knowledge of the construction of this
type of lock you can usually open them quite easily and determine
the combination. There are four methods commonly used to open
combination locks, I will briefly discuss all four.
The first method is called manipulation, which is a highly
skilled field of locksmithng that ver few are able to master. Safe
and combination lock manipulation is a specialized field of the
locksmith trade. The type of locks that you will usually run into
are the cheap inexpensive ones which aren't worth the time to
manipulate. Generally manipulation is not even a last resort;
generally manipulation is always ignored.
A common method of opening is to drill a small hole in the case
to trip the locking mechanism, or read the combination. Some locks
can be opened by rapping the case with a soft face hammer or wooden
mallet. Others can be opened by codes, but only if you have a code
book.
I highly suggest buying a master padlock and peeling the back
cover off of it to reveal the internal mechanisms. You should be
able to identify: the shackle, locking pawl, locking dog, and three
tumbler gates. Each manufacturer will have some variation of the
actual construction, however, they all operate in almost the same
manner.

DRILLING
Drill a hole approximately 1/16" in diameter. To find out
approximately where to drill, draw a line for the 'M' in Master on
the back of the lock. A straight line for the edge, through the
'M', and just missing the '.' in WIS on the other side. Now once
you have the holw drilled, take a pen light, and look in and read
the tumblers. Through the hole you should be able to see the
locking pawl and the tumbler gates. Line the tumbler gates up with
the locking pawl. Do this by first clearing the lock by turning the
dial knob at least two turns to the right, or clockwise as you face
the front side. Holding the lock in your left hand, continue
turning the dial clockwise slowly, and look through the hole you
drilled in the back. Now stop turning the dial when the gate of the
first tumbler lines up with the pawl. Now slowly turn the dial in
the opposite direction, notice the #2 or middle tumbler, does not
move at first. After one revolution, it will begin to turn.
Continue turning slowly until the gate of the #2 tumbler lines up
perfectly with the gate of the first tumbler. Next, reverse the
dial rotation and slowly turn it clockwise until the gate of the #3
tumbler lines up with the gates of the #1 and #2 tumblers. Now pull
out on the shackle and the lock will open if you line up the three


MASTER COMBINATION LOCKS Page 1



TC PUBLICATIONS


tumblers properly.

RAPPING
Sometimes you can open these locks by rapping them open by
hitting them with a soft face hammer or wooden mallet. A sudden
blow on the opposite side of the locking dog will sometimes depress
the locking spring and release the dog, allowing the shackle to come
out.

DRILLING METHOD #2 (MASTER)
On the back right hand side of the lock, draw a 3/8" line down
from where the shackle meets the lock case(inside of loop, not
outside!), then draw and 3/8" line at a 90 degree angle to that one.
Now, if you have drawn your lines right, you should be able to
drill right next to your pin-point created by the lines. NOTE:
This will destroy the lock, but it is a fail safe method of opening
and opening it fast.

CLOSING
I have seen many small files on the Master combination lock,
but all of them usually talked about the manipulation method.
Hopefully some of you out there will read this file and realize that
these methods really work. This file may be destributed freely, but
please don't re-write it and take credit for it when you don't have
any solid facts to back up the fact that you wrote it.

--------------------------------------------------------------------
TC PUBLICATIONS -- APRIL 29, 1991 -- "Master Combination Locks"
--------------------------------------------------------------------

















MASTER COMBINATION LOCKS Page 2


 
To the best of our knowledge, the text on this page may be freely reproduced and distributed.
If you have any questions about this, please check out our Copyright Policy.

 

totse.com certificate signatures
 
 
About | Advertise | Bad Ideas | Community | Contact Us | Copyright Policy | Drugs | Ego | Erotica
FAQ | Fringe | Link to totse.com | Search | Society | Submissions | Technology
Hot Topics
Free Logitech Products Wihtout Owning
Urban Exploration
graffiti on google earth.
joining the military.
Cutting the gas line
How do I get rid of my roommate?
The Xbox 360 switch
How to Really Succeed at Bad Ideas
 
Sponsored Links
 
Ads presented by the
AdBrite Ad Network

 

TSHIRT HELL T-SHIRTS