About
Community
Bad Ideas
Guns & Weapons
Irresponsible Activities
KA-FUCKING-BOOM!
Locks and Security
Scams and Rip-offs
Drugs
Ego
Erotica
Fringe
Society
Technology
register | bbs | search | rss | faq | about
meet up | add to del.icio.us | digg it

The True Combustion Cannon

by Ghetto_Smurf


NOTICE: TO ALL CONCERNED Certain text files and messages contained on this site deal with activities and devices which would be in violation of various Federal, State, and local laws if actually carried out or constructed. The webmasters of this site do not advocate the breaking of any law. Our text files and message bases are for informational purposes only. We recommend that you contact your local law enforcement officials before undertaking any project based upon any information obtained from this or any other web site. We do not guarantee that any of the information contained on this system is correct, workable, or factual. We are not responsible for, nor do we assume any liability for, damages resulting from the use of any information on this site.

Although the operation of this object is very fun and can be almost addictive, DO NOT AIM THIS MACHINE AT ANYONE! It is very likely that it will cause major and pottentialy irreversable harm to that person! Many people I know have had to spend a night or two in the hospital for missuse of it! Don't be irresponsable by trying to take it to the 'next level.' Now that that is done, here goes the instructions.

Don't be annoyed by those "other" files. This one will be the easiest to understand and visualize!

Quantity---Materials you need! (*** Don't substitute)

1 4" diam. Sch 40. ABS 3' length
1 2 1/2" diam. Sch 40. ABS 5 1/2' length (or less)
1 4" to 2 1/2" ABS reducer
1 B-B-Q lighter (the red button attached to b-b-q's)
1 125 mL. ABS cement, medium grey ***
1 4" diam. Sch 40. ABS Cleanout Adapter (female threads)
1 4" diam. Sch 40. ABS Cleanout Adapter Plug (male threads)
1 1/4" bolt. 3" long w/fitting nut

Instructions

First you will want to layout all your parts. Do this now.

You will want to start with the Cleanout Adapter plug, next you will want to set down the Cleanout Adapter. Then the 4" diam ABS pipe, above that you will want to set down the b-b-q lighter. After the 4" diam. pipe, put down the reducer, then finally the 2 1/2" diam. ABS pipe.

It should look like this---> (No Scale)

[Cleanout Adapter plug]
------------------------ 	
[Cleanout Adapter]
-------------------
[4" diam. ABS pipe] 
|	            |
|	            |
|	            |  [b-b-q lighter]
|	            |
|	            |
|	            |
[4" to 2 1/2" reducer]
-----------------
[2 1/2" diam. ABS pipe]
|	                  |
|	                  | {nut & bolt}
|	                  |
|	                  |
|	                  |
|	                  |
|	                  |
|	                  |
|	                  |
|	                  |
|	                  |						
|	                  |
__________________________

Test the fitting of the 2 12" ABS pipe and the reducer, and mark the length that goes in. Go up 1" and drill a hole big enough to push the bolt through both sides. Tighten the nut securly. Apply ABS cement to the end of the 2 1/2" diam ABs pipe that was marked. Quickly and tightly push the cemented end into the 2 1/2" hole in the reducer. Next, take the 4" diam. ABS pipe and drill a hole through one side. The exact or closest diam.of the b-b-q lighter (the end with the two leads!). Insert the end with leads into the hole, and apply cement around the exterior of the hole and b-b-q lighter. Let all the cement set for five minutes. Next apply cement to an end on the 4" diam. ABS pipe. Quickly and tighly push the cemented end into the 4" hole in the reducer. Now your construction should be a barrel with a reducer to a canister with a lighter on it.To finish to need to apply cement to the other end on the 4" diam. ABS pipe, and now for the finishing touches...quickly and tightly push the cemented end into the Cleanout Adapter (not on the threaded end!). You will also need to screw on the Cleanout Adapter Cap, but don't get any cement on that piece, this is extremly vital!

Advanced Procedures

If you want, you can get a file or grinder and grind the end of the 2 1/2" diam. ABS pipe so that it is sharp. This is so that you can jam a potato through the end and it automatically fits the barrel.

Propellants

Hair spray (two spray bursts)
Butane (small bursts)
Gasoline (two drops or so, but let the drops turn into their gas state)
Zippo fluid/lighter fluid
Hydroger (untested)
Methane (untested)
Propane
Deodorant
**Please be cautious!

Projectiles (some may need to be wadded {see below})

The reason I asked you to put in the nut and bolt is so that when you stuff you barrel, the projectile will stop exactly where it should and it will not fall into the combustion chamber.

Potatoes
PVC conduit pipe darts (see below)
Paint Ball cluster bombs (See below)
Hard boiled eggs
Soda cans
Smoke bombs
Ice slug (see below)
Shrapnel (chunks of scrap metal)
B-B's
Batteries
A glowing bag (see below)
Fruits and veggies
And almost anything else that will fit into the barrel
Use your imagination

Projectile Instructions

PVC conduit pipe darts

You will need a length of pvc conduit (small diam. than your barrel), any length. Cut the conduit at 9" length intervals starting from the female end. Not find a wooden cylinder, like a broom handle or something that it thicker than the hole in the conduit. Now get some sand paper and sand down the wood so that it is about 1mm or 2 thicker than the hole, then cut off about 1" - 3/4". Jam that wood through the end so that 2mm stick out (not flush with the conduit). *If you choose, you can apply some pvc cement to the wood befor you jam it in, although I am not sure if it helps. Next put about 2" of pennies inside the barrel (if you put them in flat you will get more per area) or enough to make the tip weighted, but never go past the half way mark in the 9".now get a piece of old clotch and cut a strip 2" wide and 1 1/2' long. Roll this strip of cloth up tight. Test fit it, if it is too wide, cut off some length. Now slop on lots of pvc cement to that baby and jam it all the way down the conduit to make contace with the pennies... get a stick and jam it in some more. ..you want it tight! Now it should be heavy in one end and light on the other. The balance point should be somewhere between the wood and the half-way mark. If it is past, then the dart may tilt down and not fly straight. Get some masking tape (1 1/2" wide) and wrap it around the open end of the conduit. Continue wrapping it until it fits your barrel snugly! Not lose, make sure it is so snug that it must be forced down the barrel, but with some ease. The snugness makes sure that no air escapes which means that the dart will go VERY FAR. These things are very dangerous...if someone is hit with one of these they will die! I'm not kidding, I have been testing these things at different distances and amounts of firing mixtures and I have put one of these rockets through 3/4" plywood, cleanly. I mean so clean that you can't see any slivers left on either side!

Paint Ball cluster bombs

You will need a handful of paint balls, and two plastic or styrofoam cups. Take a cup, put the bottom of the cup into the barrel, and make a line all the way around the cup, repeat that for the second cup. Not cut off the bottom of the cup at the line. Get some super glue and glue the ends together so it should be open end, then closed end, then open end. Now slide that down your barrel to the end. Get the handful of paintballs and put them on a paper towel. Grab each corner and bring them up to meat each other. Twist the paintballs up and run the clump of paintballs trough a mist of water to get the papaer towel wet. Slid this down the barrel, but carefully so that the paper towel does not rip or tear. When fired, this things goes out and on contact with explode with a white creamy and colorful mess or paper and paint.

Ice Slugs

Cut a length of 2 1/2" ABS pipe from the end of your barrel (or swipe it from somewhere). Now take an end and cover it with duct tape, so no water can leak out from it. Fill the pipe half full of water then put it in the freezer for 4 hours, then finish filling the pipe. Put back in freezer and let if freeze overnight. Next morning take it out, slide it from the casing and slide it into your barrel, it fits perfectly and can have major damaging effects!

A glowing bag (Make the same night of use)

Take some gardening cloth and make a ball of crumpled up cloth that will fit inside your barrel. Take another piece of cloth and cover the crumpled ball the same way with the painballs. Twist it and tie it. Now get a whole bunch of glowing stuff like the glowing paint, glowing glue, or just a bunch of glowing sticks that have been broken and put it all in a bucket. Now dunk the ball into the glowing mixture and leave it submerged for a few minutes to make sure it is saturated. Make a few of them and repeat. Leave them in the glowing stuff until you use them. Now quickly take one (with gloves on) and jam it down the barrel and fire it to oblivion. When it hits something, it makes a huge glowing mess, and while in flight looks really cool!

 
To the best of our knowledge, the text on this page may be freely reproduced and distributed.
If you have any questions about this, please check out our Copyright Policy.

 

totse.com certificate signatures
 
 
About | Advertise | Bad Ideas | Community | Contact Us | Copyright Policy | Drugs | Ego | Erotica
FAQ | Fringe | Link to totse.com | Search | Society | Submissions | Technology
Hot Topics
Detonation by fire?
would this work???
so I've been googling around but:
Books
SHOOTER MOVIE ((Hollywood vs. Reality))
is nitro cellulose sensitive to small arms fire?
potassium nitrate
How to make many small, controlled explosions?
 
Sponsored Links
 
Ads presented by the
AdBrite Ad Network

 

TSHIRT HELL T-SHIRTS